ブログに戻る
ハウツーガイド 2026-11-20 Bicycle Superstore 0 ビュー

Shimano Road Brake Cable Set Installation Tips

Shimano Road Brake Cable Set Installation Tips

Learn how to install and route your Shimano road brake cable set. Includes cable lengths, inner and outer cable specs, and tips for drop bar shifters.

What the Shimano Road Brake Cable Set Includes

The Shimano Road Brake Cable Set is a genuine replacement kit for road bikes or other drop bar shifters. It contains front and rear inner cables, outer cables, ferrules, and inner end caps. The set uses stainless steel inner cables and an SLR outer cable, which is designed for responsive braking with road levers.

Knowing what comes in the box helps you plan the job and avoid buying extra parts you don't need.

Cable Lengths That Matter for Routing

  • Shimano Road Brake Cable Set: 1 x SLR Brake Cable Outer: Length 2200mm x Diameter 5mm 2200 mm of outer cable is enough for most road bike frames, including those with external or internal routing. The 5 mm diameter fits standard cable stops and ferrules.
    Shimano Road Brake Cable Set
    Shimano Road Brake Cable Set
  • Shimano Road Brake Cable Set: 1 x Stainless Steel Rear Inner Brake Cable: Length 2050mm x Diameter 1.6mm 2050 mm rear inner cable is sufficient for a rear brake run, even on larger frames. The 1.6 mm diameter is the standard Shimano road brake size.
  • Shimano Road Brake Cable Set: 1 x Stainless Steel Front Inner Brake Cable: Length 1000mm x Diameter 1.6mm 1000 mm front inner cable is typically enough for a front brake, but check your frame's routing path before cutting. The 1.6 mm diameter matches the rear cable.

Step-by-Step Installation Guide

Installing a new brake cable set improves braking feel and safety. Follow these steps using the supplied components.

  1. Remove old cables: Loosen the brake caliper anchor bolt and pull the old inner cable out. Remove the outer cable from the frame guides.
  2. Prepare the new outer cable: Cut the 2200 mm SLR outer cable to length if needed. Slide a ferrule onto each end. Use the supplied ferrules to prevent fraying and ensure a snug fit in the cable stops.
  3. Route the outer cable: Guide the outer cable through the frame's cable guides or internal routing ports. For drop bar shifters, the outer cable runs from the lever to the first cable stop on the frame.
  4. Install the inner cable: Thread the appropriate inner cable (1000 mm front or 2050 mm rear) through the outer cable. Attach the inner end cap to the cable end that goes into the lever.
  5. Connect to the brake caliper: Pass the inner cable through the caliper anchor bolt. Pull the cable taut and tighten the bolt. Check that the brake arms move freely and the pads contact the rim evenly.
  6. Trim and cap: Cut any excess inner cable, leaving the recommended length beyond the anchor bolt as specified in the product instructions. Crimp a cable end cap to prevent fraying.

Routing Tips for Drop Bar Shifters

The Shimano Road Brake Cable Set is designed for road bikes with drop bar shifters. When routing the outer cable from the shifter to the frame, avoid sharp bends that could cause friction. The SLR outer cable's 5 mm diameter provides low-compression performance, but kinking will still affect braking response.

For internal routing frames, use a guide wire or magnet to pull the outer cable through the frame. The 2200 mm length gives you enough slack to work with, even on larger frames.

Choosing the Right Cable Set for Your Bike

If you only need to replace a single inner cable, the Shimano Road Brake Inner Cable (2050 mm, 1.6 mm) is a cost-effective option. It includes a cable end and fits the same drop bar shifters. The full set is better if you're replacing both front and rear cables or need new outer cables.

Shimano Road Brake Inner Cable
Shimano Road Brake Inner Cable

Both options use genuine Shimano stainless steel construction, which resists corrosion and provides consistent braking feel.

関連記事

Customer Service
ホーム
商品
カート
マイページ